Exhaust Clip Sticky

silvr z said:
I ran one with high flow cats for a few years and for a little with long tubes.
Click to expand...

My setup right now is high flow cats and a single 12 inch bullet to a dumped 8 inch tip. Piping is three inches. I want louder and cutting out the cats seems like the cheapest way to get that, but I don't want it sounding like complete shit haha

Sent from my SCH-R760 using Tapatalk 2
 
tanner said:
My setup right now is high flow cats and a single 12 inch bullet to a dumped 8 inch tip. Piping is three inches. I want louder and cutting out the cats seems like the cheapest way to get that, but I don't want it sounding like complete shit haha

Sent from my SCH-R760 using Tapatalk 2
Click to expand...
You will be somewhere between those two sounds. I wouldn't say either setup sounded bad, but my truck was pretty loud with the headers into bullet dumped. It just got annoying but I always thought it sounded good.

You will have to tune out your o2 sensors if you cut the cats off so that's an added expense.
 
silvr z said:
You will be somewhere between those two sounds. I wouldn't say either setup sounded bad, but my truck was pretty loud with the headers into bullet dumped. It just got annoying but I always thought it sounded good.

You will have to tune out your o2 sensors if you cut the cats off so that's an added expense.
Click to expand...

I will still have stock manifolds for a while though, so how will that affect the sound compared to headers?
 
tanner said:
I will still have stock manifolds for a while though, so how will that affect the sound compared to headers?
Click to expand...

It's just going to sound a bit less throaty honestly, nothing to be concerned with. Cutting cats off will make it more raspy than what it is now and it will be louder.
 
damn, I guess I never posted my setup. currently have Magnaflow 18" muffler s in/d out. About to throw my Pacesetter's on with their ory pipe and new cats, all 3" piping, 22" Magnaflow dumped behind the axle.


[video=youtube_share;J1_lUQub9nk]http://youtu.be/J1_lUQub9nk[/video]

[video=youtube_share;n2Do9oGzs_c]http://youtu.be/n2Do9oGzs_c[/video]
 
Last edited:

idle and slowly bringing it up to 2000 RPM, all stock other than Cherry Bomb Extreme and the factory tailpipe hacked off
 
just installed my borla xr-1 back on why do i feel like it got way quieter then when i had it on the first time ?
 
06fourdoe said:
just installed my borla xr-1 back on why do i feel like it got way quieter then when i had it on the first time ?
Click to expand...

I just installed a xr1 too it is quieter at idle but it has a nice deep tone really happy with it. Also no more rasp that I had with lts n flowmaster 10 series.
 
I know its supposed to be quite but I can't even hear it when I step on it like I used to

Sent from my SCH-I535 using Tapatalk
 
Cam 5.3l first start up, open headers.


Cam 6.0l first start up, open headers.


In cab- 6.0l, CalSpeed longtube headers, ory, single 3" 18" Dynomax Bullet in front of an Aeroturbine 3030xl, 4" dmax tailpipe to a 6" tip...exhaust leaks like a mofo.


Same exhaust as above, but 5.3l


Cammed 5.3l, Pacesetter longtubes, ory, Aeroturbine 3030xl, 4" tailpipe. No Bullet in front of Aero. Excuse the dirty ass truck.


Still don't have a good walk around vid of current setup. Getting tired of aeroturbine's drone....
 
Fiesty said:
Cam 5.3l first start up, open headers.


Cam 6.0l first start up, open headers.


In cab- 6.0l, CalSpeed longtube headers, ory, single 3" 18" Dynomax Bullet in front of an Aeroturbine 3030xl, 4" dmax tailpipe to a 6" tip...exhaust leaks like a mofo.


Same exhaust as above, but 5.3l


Cammed 5.3l, Pacesetter longtubes, ory, Aeroturbine 3030xl, 4" tailpipe. No Bullet in front of Aero. Excuse the dirty ass truck.


Still don't have a good walk around vid of current setup. Getting tired of aeroturbine's drone....
Click to expand...

I have the 3030 non resonated and no drone here but I also dont have headers like yourself
 
You must log in or register to reply here.
Top Bottom