It's not up to my liking yet so it won't be posted until passes my initial tests of liking
But it may be sold so we'll see!
Marc new LBZ sort of a Build thread
- Thread starter marc
- Start date
It's not up to my liking yet so it won't be posted until passes my initial tests of liking
But it may be sold so we'll see!
ok so here is a pic of the plasti dip i did (temporarily) just too see if i am leaving the grille chrome or painting it white.
so i have taken care of every little problem on this truck, front diff re-sealed, transfer case pump rub fix and put a transgo JR in it.
now its ready for a bit more go go.
so here is the SDP EGR delete, and LB7 up-pipe, both will be cleaned up and painted, or powdered gloss black or silver.
also ordering soon is a down-pipe, lift pump, PPE ported fuel rail fittings, PPE race plug and then that will all get done in a day/weekend.
after that is some real tunes...should be fun.
so i have taken care of every little problem on this truck, front diff re-sealed, transfer case pump rub fix and put a transgo JR in it.
now its ready for a bit more go go.
so here is the SDP EGR delete, and LB7 up-pipe, both will be cleaned up and painted, or powdered gloss black or silver.
also ordering soon is a down-pipe, lift pump, PPE ported fuel rail fittings, PPE race plug and then that will all get done in a day/weekend.
after that is some real tunes...should be fun.
:truestory: I was looking at prices of a 68mm cheetah or Danville billet turbo....but that will be a while yet, but at least I will have all the other small stuff done
Sent from my iPad using Tapatalk
so i just got the truck back from the shop tranny is all good now, there was a bur on once of the valves and it was stuck.
i will be taking my truck on a 2600km 1600 mile trip to go snowboarding, while my front diff is still leaking quite a bit.
i also had a strange noise coming from the truck, jacked up my truck and seen that i needed tie rods which i knew was coming, and also a pit-man arm, idler arm, and the steering braces. .... so i will be ordering this kit i think. DMAXSTORE Ultimate Front End Package Stage 2 | DMAX Store
unless someone has a better option.
now the power adders will have to wait again.
i will be taking my truck on a 2600km 1600 mile trip to go snowboarding, while my front diff is still leaking quite a bit.
i also had a strange noise coming from the truck, jacked up my truck and seen that i needed tie rods which i knew was coming, and also a pit-man arm, idler arm, and the steering braces. .... so i will be ordering this kit i think. DMAXSTORE Ultimate Front End Package Stage 2 | DMAX Store
unless someone has a better option.
now the power adders will have to wait again.
the place that have axle shafts for $125/side for the front diff is out of stock...and all other places the prices are $300+ for driver side and $400+ for passenger side....
might be picking up front diff tomorrow too pull the shafts out of that one....:shrug: so much BS...
if it was possible to SAS it, and keep it at this height, or no more then 3" higher, for less then 2k, and still ride nice i would
just install my piaa 4000k extreme white plus headlights ....they are not as white as i hoped... but i will be keeping them for now, as they are a lot brighter then my original lights.
also should be receiving my diodes to do 6 high mod at the end of this month.
also should be receiving my diodes to do 6 high mod at the end of this month.
i ordered them on ebay they came from Australia iirc
read LED thread...i didn't want to blind people.
not really, now instead of spending $1000 on doing my engine performance shit, i have to spend it on building my front end....
yeah and another thing is i cant really afford to have down time since my truck is used for work eveyday.